Bearing Failures On
                      1973-74 Chrysler (Dodge) 3.7L (225 CID) Engines

Low mileage main and rod bearing failures have been reported in 1973-74 Chrysler (Dodge) 3.7L (225 CID) car and truck engines. 

It appears that the failures were caused by the oil galleries to the main bearings being misdrilled or restricted by metal chips from machining.

When these failures occur, the following procedure is recommended:

If the crankshaft is still installed, loosen all main bearing cap screws on the right (camshaft side) finger loose. Remove the engine oil filter and apply 30 to 50 psi air pressure into the standpipe fitting. Check to be sure that air and oil are coming from the loose main bearing cap screws.

In cases where the crankshaft has been removed, detach the engine oil filter and direct 5 to 10 psi air pressure into the standpipe fitting. Check to be sure that air is coming from the oil gallery to main bearing hole at all main bearing locations.

The cylinder block oil passage from the main bearing to the oil gallery should be carefully checked for misdrilling or plugging with machine chips on any bolt that does not show a flow of air and oil.

                                                                          The AERA Technical Committee

                          Flywheel Depths For Heavy Duty Truck Applications

The AERA Technical Committee offers the following information on flywheel depths for heavy-duty truck applications. Many problems occur when machining 
recessed flywheels (cup type) if the correct depth is not re-established. For proper clutch operation to occur, the correct flywheel depth and clutch components must be verified before installation.

        Application                              Depth +/- .005

     12 B&B 2 PI. Dodge                          1.153
     13 B&B 2 PI. Dodge                          1.153
     13 Ford 2 PI.                                      1.470
     14 Lipe                                               1.187
     14 Lipe M                                           1.812
     14 Lipe PT                                         2.937
     14 Long                                              1.187
     14 Mack                                             1.595
     14 Rockford                                       1.187
     14 Spicer 1 P                                     1.812
     14 Spicer 2 P                                     2.937
     15 Lipe M                                           1.812
     15 Lipe DP                                         1.750
     15 Mack                                              1.595
     15 Mack 2 P                                       2.796
     15 Rockford                                       1.750
     15 ? Lipe TC                                      1.225
     15 ? Long                                           1.325
     16 ? German Mack F&S                       .670
     17 Lipe TC 1 P                                   1.218
     17 Lipe TC 2 P                                   2.321

                                   Riser Types
     
      13 Lipe AK 204                                  1.062
      13 Lipe AK 209                                  1.062
      13 Lipe AK217                                   1.062
      13 Long                                              1.250
      14 Lipe AK 206                                  1.093
      14 Lipe AK 208                                  1.093

                                                        The AERA Technical Committee

                                      Engine Bolt Torque Information On
                             GM (Chevrolet) 1977 L-4, L-6 & V-8 Engines

Chevette L-4 Engine Torque Bolt Specifications

Usage Torques
---------------------------------------------------------------------------

Camshaft Carrier Bolts 90-95Nm 65-77 ft.lbs.
Camshaft Cover Nuts 1.4-1.8Nm 12-16 in.lbs.
Camshaft Sprocket Bolt 90-115Nm 65-85 ft.lbs.
Crankshaft Pulley Bolt 90-115Nm 65-85 ft.lbs.
Crankcase Front Cover Bolt 6-8Nm 55-75 in.lbs.
Front Cover Nut 5-8Nm 50-75 in.lbs.
Connecting Rod Nuts 46-54Nm 34-40 ft.lbs.
Coil Attaching Bolt 18-24Nm 13-18 ft.lbs.
Distributor Clamp Bolt 15-19Nm 11-14 ft.lbs.
Exhaust Manifold 26-34Nm 19-25ft.lbs.
Flywheel Bolt 54-75Nm 40-52 ft.lbs.
Fuel Pump Bolts 19-23Nm 14-17 ft.lbs.
Generator Bracket Bolt 30-40Nm 22-30 ft.lbs.
Idler Pulley Bolt 18-24Nm 13-18 ft.lbs.
Intake Manifold Bolt 18-24Nm 13-18 ft.lbs.
Main Bearing Caps 54-75Nm 40-52 ft.lbs.
Oil Drain Plug 20-27Nm 15-20 ft.lbs.
Oil Pan Bolts 5-7Nm 45-60 in.lbs.
Oil Suction Tube & Screen Ass. 26-34Nm 19-25 ft.lbs.
Oil Suction Tube Clamp 95-130Nm 70-95 in.lbs.
Oil Filter 16-23Nm 12-17 ft.lbs.
Oil Pump Cover Screws 8-11Nm 71-97 in.lbs.
Oil Pump Bolts 5-7Nm 45-60 in.lbs.
Water Pump Bolts 18-24Nm 13-18 ft.lbs.
Spark Plugs 27Nm 20 ft.lbs.


Vega - Monza L-4 Engine Bolt Torque Specifications

Size Usage Torque
----------------------------------------------------------

1/4-14 Engine Front Cover 50 in.lbs.
1/4-20 Cam Cover 80 in.lbs.
1/4-20 Oil Screen To Screen 50 in.lbs.
1/4-20 Clutch Housing Underpan 95 in.lbs.
1/4-20 Oil Screen Support To Baffle 50 in.lbs.
1/4-20 Oil Drain Back Tube To Baffle 50 in.lbs.
5/16-18 Fan Blade To Pump 20 ft.lbs.
5/16-18 Clutch Pressure Plate To Fly. 20 ft.lbs.
5/16-18 Crankshaft Damp/Pulley Sprkt. 15 ft.lbs.
5/16-18 Oil Pump To Case (Bolt) 15 ft.lbs.
5/16-18 Water Pump To Case 15 ft.lbs.
5/16-18 Oil Pan To Case 15 ft.lbs.
5/16-18 Cam Retainer 18 ft.lbs.
5/16-24 Ex. Gas Recirc. Valve To Man. 20 ft.lbs.
11/32-24 Connecting Rod Cap 35 ft.lbs.
3/8-16 Oil Pump To Case (Stud) 30 ft.lbs.
3/8-16 Distributor Clamp Nut 25 ft.lbs.
3/8-16 Water Outlet To Head 30 ft.lbs.
3/8-16 Manifold (Bolts) 30 ft.lbs.
3/8-16 Clutch Housing To Case 25 ft.lbs.
3/8-16 Clutch Pressure Plate To Fly. 30 ft.lbs.
3/8-18 Inlet Manifold To Head (Stud) 30 ft.lbs.
7/16-14 Engine Mount Stud To Block 20 ft.lbs.
7/16-14 Main Bearing Caps 65 ft.lbs.
7/16-14 Cylinder Head 60 ft.lbs.
7/16-20 Flywheel To Crank 65 ft.lbs.
1/2-13 Cam Sprocket To Cam 80 ft.lbs.
1/2-13 Damper/Pulley To Crank 80 ft.lbs.
1/2-20 Oil Pan Drain Plug 20 ft.lbs.
1.00-12 Oil Filter Connector To Case 30 ft.lbs.
1.00-12 Oil Filter Hand Tight
14mm Spark Plug 20 ft.lbs.


In-Line 4.1L (250 CID) Car - Truck Engine Bolt Torques

Size Usage Torque
----------------------------------------------------------------

1/4-20 Cam Thrust Plate 80 in.lbs.
1/4-20 Crankcase Front Cover 80 in.lbs.
1/4-20 Flywheel Housing Cover 80 in.lbs.
1/4-20 Oil Filter Bypass Valve 80 in.lbs.
1/4-20 Oil Pan To Crankcase 80 in.lbs.
1/4-20 Oil Pan To Front Cover 50 in.lbs.
1/4-20 Oil Pump Cover All 80 in.lbs.
1/4-20 Rocker Arm Cover 45 in.lbs.
11/32-24 Connecting Rod Cap 35 ft.lbs.
5/16-18 Camshaft Sprocket 20 ft.lbs.
5/16-18 Oil Pan To Crankcase 80 in.lbs.
5/16-18 Oil Pump 115 in.lbs.
5/16-18 Push Rod Cover 80 in.lbs.
5/16-18 Water Pump 15 in.lbs.
5/16-18 Rocker Cover 45 in.lbs.
3/8-16 Clutch Pressure Plate (All) 30 ft.lbs.
3/8-16 Distributor Clamp 25 ft.lbs.
3/8-16 Flywheel Housing 30 ft.lbs.
3/8-16 Manifold (Exhaust) 35 ft.lbs.
3/8-16 Manifold (Ex. To Int.)
3/8-16 Manifold (Intake) 30 ft.lbs.
3/8-16 Manifold To Head
3/8-16 Thermostat Housing 30 ft.lbs.
3/8-16 Water Outlet 30 ft.lbs.
3/8-16 Water Pump
3/8-24 Connecting Rod Cap
7/16-14 Cylinder Head 60 ft.lbs.
7/16-14 Main Bearing Cap 65 ft.lbs.
7/16-14 Oil Pump 65 ft.lbs.
7/16-14 Rocker Arm Stud 50 ft.lbs.
7/16-20 Flywheel (All) 45 ft.lbs.
7/16-20 Torsional Damper 60 ft.lbs.
1/2-13 Cylinder Head 95 ft.lbs.
1/2-13 Main Bearing Cap 110 ft.lbs.
1/2-14 Temperature Sending Unit 20 ft.lbs.
1/2-20 Torsional Damper
1/2-20 Oil Filter Hand Tight
1/2-20 Oil Pan Drain Plug 20 ft.lbs.
1/2-20 Flywheel
14mm 5/8 Spark Plug 15 ft.lbs.


In-Line 4.8L (292 CID) Passenger Car - Truck Engine Bolt Torque

Size Usage Torque
----------------------------------------------------------------

1/4-20 Cam Thrust Plate 80 in.lbs.
1/4-20 Crankcase Front Cover 80 in.lbs.
1/4-20 Flywheel Housing Cover 80 in.lbs.
1/4-20 Oil Filter Bypass Valve
1/4-20 Oil Pan To Crankcase 80 in.lbs.
1/4-20 Oil Pan To Front Cover 50 in.lbs.
1/4-20 Oil Pump Cover All 80 in.lbs.
1/4-20 Rocker Arm Cover 45 in.lbs.
11/32-24 Connecting Rod Cap
5/16-18 Camshaft Sprocket 20 ft.lbs.
5/16-18 Oil Pan To Crankcase 80 in.lbs.
5/16-18 Oil Pump 115 in.lbs.
5/16-18 Push Rod Cover 80 in.lbs.
5/16-18 Water Pump 15 in.lbs.
5/16-18 Rocker Cover 45 in.lbs.
3/8-16 Clutch Pressure Plate (All) 30 ft.lbs.
3/8-16 Distributor Clamp 25 ft.lbs.
3/8-16 Flywheel Housing 30 ft.lbs.
3/8-16 Manifold (Exhaust)
3/8-16 Manifold (Ex. To Int.) 40 ft.lbs.
3/8-16 Manifold (Intake) 30 ft.lbs.
3/8-16 Manifold To Head 40 ft.lbs.
3/8-16 Thermostat Housing 30 ft.lbs.
3/8-16 Water Outlet 30 ft.lbs.
3/8-16 Water Pump 25-30 ft.lbs.
3/8-24 Connecting Rod Cap
7/16-14 Cylinder Head
7/16-14 Main Bearing Cap 65 ft.lbs.
7/16-14 Oil Pump
7/16-14 Rocker Arm Stud
7/16-20 Flywheel (All) 45 ft.lbs.
7/16-20 Torsional Damper 60 ft.lbs.
1/2-13 Cylinder Head 95 ft.lbs.
1/2-13 Main Bearing Cap
1/2-14 Temperature Sending Unit 20 ft.lbs.
1/2-20 Torsional Damper
1/2-20 Oil Filter Hand Tight
1/2-20 Oil Pan Drain Plug 20 ft.lbs.
1/2-20 Flywheel 110 ft.lbs.
14mm 5/8 Spark Plug 15 ft.lbs.


Small V-8 5.0, 5.7 & 6.6L Passenger Car - Truck Engine Bolt Torques

Size Usage Torque
----------------------------------------------------------------

1/4-20 Cam Thrust Plate
1/4-20 Crankcase Front Cover 80 in.lbs.
1/4-20 Flywheel Housing Cover 80 in.lbs.
1/4-20 Oil Filter Bypass Valve 80 in.lbs.
1/4-20 Oil Pan To Crankcase 80 in.lbs.
1/4-20 Oil Pan To Front Cover
1/4-20 Oil Pump Cover All 80 in.lbs.
1/4-20 Rocker Arm Cover 45 in.lbs.
11/32-24 Connecting Rod Cap
5/16-18 Camshaft Sprocket 20 ft.lbs.
5/16-18 Oil Pan To Crankcase 165 in.lbs.
5/16-18 Oil Pump
5/16-18 Push Rod Cover
5/16-18 Water Pump
5/16-18 Rocker Cover
3/8-16 Clutch Pressure Plate (All) 30 ft.lbs.
3/8-16 Distributor Clamp 25 ft.lbs.
3/8-16 Flywheel Housing 30 ft.lbs.
3/8-16 Manifold (Exhaust) 20 ft.lbs.
3/8-16 Manifold (Ex. To Int.)
3/8-16 Manifold (Intake) 30 ft.lbs.
3/8-16 Manifold To Head
3/8-16 Thermostat Housing
3/8-16 Water Outlet 30 ft.lbs.
3/8-16 Water Pump 25-30 ft.lbs.
3/8-24 Connecting Rod Cap 45 ft.lbs.
7/16-14 Cylinder Head 65 ft.lbs.
7/16-14 Main Bearing Cap 60 ft.lbs.
7/16-14 Oil Pump 65 ft.lbs.
7/16-14 Rocker Arm Stud
7/16-20 Flywheel (All) 65 ft.lbs.
7/16-20 Torsional Damper 60 ft.lbs.
1/2-13 Cylinder Head
1/2-13 Main Bearing Cap
1/2-14 Temperature Sending Unit 20 ft.lbs.
1/2-20 Torsional Damper
1/2-20 Oil Filter 25 ft.lbs.
1/2-20 Oil Pan Drain Plug 20 ft.lbs.
1/2-20 Flywheel
14mm 5/8 Spark Plug 15 ft.lbs.


Mark IV V-8 Engine Bolt Torques

Size Usage Torque
----------------------------------------------------------------

1/4-20 Cam Thrust Plate
1/4-20 Crankcase Front Cover 80 in.lbs.
1/4-20 Flywheel Housing Cover 80 in.lbs.
1/4-20 Oil Filter Bypass Valve 80 in.lbs.
1/4-20 Oil Pan To Crankcase
1/4-20 Oil Pan To Front Cover 55 in.lbs.
1/4-20 Oil Pump Cover All 80 in.lbs.
1/4-20 Rocker Arm Cover 50 in.lbs.
11/32-24 Connecting Rod Cap
5/16-18 Camshaft Sprocket 20 ft.lbs.
5/16-18 Oil Pan To Crankcase 135 in.lbs.
5/16-18 Oil Pump
5/16-18 Push Rod Cover
5/16-18 Water Pump
5/16-18 Rocker Cover
3/8-16 Clutch Pressure Plate (All) 30 ft.lbs.
3/8-16 Distributor Clamp 25 ft.lbs.
3/8-16 Flywheel Housing 30 ft.lbs.
3/8-16 Manifold (Exhaust) 20 ft.lbs.
3/8-16 Manifold (Ex. To Int.)
3/8-16 Manifold (Intake) 30 ft.lbs.
3/8-16 Manifold To Head
3/8-16 Thermostat Housing
3/8-16 Water Outlet 30 ft.lbs.
3/8-16 Water Pump 25-30 ft.lbs.
3/8-24 Connecting Rod Cap 50 ft.lbs.
7/16-14 Cylinder Head 80 ft.lbs.
7/16-14 Main Bearing Cap
7/16-14 Oil Pump 65 ft.lbs.
7/16-14 Rocker Arm Stud 50 ft.lbs.
7/16-20 Flywheel (All) 65 ft.lbs.
7/16-20 Torsional Damper
1/2-13 Cylinder Head
1/2-13 Main Bearing Cap 110 ft.lbs.
1/2-14 Temperature Sending Unit 20 ft.lbs.
1/2-20 Torsional Damper 85 ft.lbs.
1/2-20 Oil Filter 25 ft.lbs.
1/2-20 Oil Pan Drain Plug 20 ft.lbs.
1/2-20 Flywheel
14mm 5/8 Spark Plug 15 ft.lbs.

                                                                       The AERA Technical Committee

                            Internally vs. Externally Balanced Flywheels On
                                                GM 2.8L Truck Engines

AERA members should be cautious when replacing flywheels on 1986 and later Chevrolet S-10 trucks and Astro Vans equipped with manual transmissions and the 2.8L engine.

Vehicles manufactured in 1986 and 1987 use the externally balanced 2.8L engine.  This engine requires a flywheel with GM Part #14088277 which carries the casting number 14033082.

Vehicles manufactured as of the 1988 model year use an internally balanced 2.8L engine.  The flywheel for this application is available under GM Part #14100556 with the casting number 14046567.

It is physically possible to mount the incorrect flywheel to the crankshaft causing a severe engine imbalance and vibration. 

                                                                             The AERA Technical Committee

                         Air Operated Tools For Valve Train Rebuilding

Air Operated Valve Spring Compressors

The use of an air operated valve spring compressor will simplify and speed up the disassembly and assembly of cylinder heads. During both operations, this tool will hold the valve spring assembly in the compressed position so that both hands of the worker are free to remove or install the valve keepers.  Buy a
heavy duty model to handle large truck and high performance cylinder heads.

Air Impact Hammer

An air impact hammer should be used to remove and install valve guides.  This tool does the job very quickly and efficiently and when used properly, does not damage the parts.  Operator fatigue is reduced by removing the old hammer approach giving a more professional aspect to the operation.


                                                                       The AERA Technical Committee